荔湾3

中化建国际 对下列产品及服务进行国际公开竞争性招标，于2025-03-17在公告。本次招标采用传统招标方式，现邀请合格投标人参加投标。1、招标条件项目概况:荔湾3-1 气田群位于中国南海珠江口盆地白云凹陷内，距香港东南部310km，气田群所在海域水深640-1500m。荔湾3-1 气田调整开发项目通过降低荔湾3-1 气田群水下井口压力实现增产，无调整井及新建平台设施。平台增压部分在荔湾3-1CEP 平台新建3 台预增压湿气压缩机、入口涤气罐及出口冷却器和1 台段塞流捕集器，改造凝析油增压泵。平台增压部分计划于2027年1 月投用。资金到位或资金来源落实情况:已落实项目已具备招标条件的说明:已具备2、招标内容招标项目编号:0704-2540JDCP5700招标项目名称:荔湾3-1气田调整开发项目调节阀项目实施地点:中国广东省招标产品列表(主要设备):

序号	产品名称	数量	简要技术规格	备注
1	调节阀	15	详见技术文件

3、投标人资格要求投标人应具备的资格或业绩:对投标人的资格和业绩要求：Requirements for Qualification and reference of Bidder:（1）资格要求 Requirements for Qualification of Bidder A．★营业执照：如果投标人为境内注册公司，投标人需提供合法有效的企业法人营业执照、税务登记证及组织机构代码证或证照合一的营业执照；如果投标人为境外注册公司，需提供有效的公司登记注册证明。A．★Business licence: The bidder within the customs territory shall provide valid independent legal person business license, tax registration certificate, organization code certificate, or combined certificate and business license;The bidder outside the customs territory shall provide valid certificate to prove valid business registration certificate.B．★制造商要求:所投产品为国内产品：不允许代理商投标，投标人需是调节阀的制造商所投产品为境外产品：允许调节阀的制造商或取得调节阀制造商唯一授权的代理商投标。 投标人为代理商时，应得到本次投标调节阀制造商的唯一合法授权，并需提供以下材料（盖制造商公章）：1）在有效期内的调节阀制造商授权书；2）调节阀制造商承诺函，承诺投标所投产品为制造商工厂生产。B． ★ Manufacturer requirement: The product being bid for is a domestic product: agents are not allowed to bid, and bidders must be manufacturers of control valves.The product being tendered is an overseas product: manufacturers of control valves or agents authorized solely by the control valve manufacturer are allowed to bid.When the bidder is an agent or a contractor, they should obtain the sole legal authorization of the control valve manufacturer for this bidding and provide the following materials (stamped with the manufacturer's official seal):1) Authorization letter from the manufacturer of the control valve within its validity period;2) Commitment letter from the manufacturer of the control valve, promising that the products submitted for bidding will be produced by the manufacturer's factory.C．★是否接受联合体投标：否。C. ★Joint Venture: Not Accepted.D．★未领购招标文件是否可以参加投标:不可以。D. ★Bid without the bidding documents：NOT Available.（2）★资质要求及证明文件投标人所供的阀门制造商应取得由国家市场监督管理总局颁发的特种设备生产许可证（许可子项目涵盖A1及A2）及覆盖本次招标范围的由第三方颁发的特种设备型式试验证书,投标人应在投标时提供上述证书的扫描件。The manufacturers of pressure pipeline components such as valves provided by the bidder shall obtain the special equipment manufacturing license (TS A1 or A2 certificate) awarded by State Administration for Market Regulation and the special equipment type test certificate covering the scope of this bidding awarded by third party,Bidders should provide scanned copies of the aforementioned certificates during the bidding process.（3）★业绩要求Requirement for Bidder's reference:投标人需满足以下所有要求：The Bidder needs to meet all below requirements：A.From January 1, 2010 to the bidding deadline (based on the contract signing time), the control valve manufacturer submitted by the bidder must have at least 3 sets of pneumatic control valves and 2 sets of electric control valve matching supply performance. The brand and Production factory address of the control valve submitted by the bidder must be consistent with the performance of the control valve mentioned above(The Production factory address of valve PV-1503D should be consistent with the performance Production factory address corresponding to performance requirement 1, the Production factory address of other pneumatic control valves should be consistent with the performance Production factory addresss corresponding to performance requirement 2, and the Production factory address of electric control valves should be consistent with the performance Production factory address corresponding to performance requirement 3). The performance should meet or exceed the following technical requirements:Performance Requirement 1 Performance Requirement 2 Performance Requirement 3pneumatic control valve pneumatic control valve electric control valvePerformance requirement: 1 set Performance requirement: 2 set Performance requirement: 2 setbody material A182 F51 or A995 Gr.4A body material A995 Gr.4A body material A995 Gr.4ABody size ≥20” Body size ≥14” Body size ≥3”Body rating ≥1500# Body rating ≥600# Body rating ≥300#Body type V-Ball or Globe Body type Globe Body type GlobeFlow coefficient CV CV ≥ 261 at minimum flow rate.CV ≥ 1814under normal traffic conditions.CV ≥ 4201 at maximum flow rate. Flow coefficient CV CV ≥67.4 at minimum flow rate. CV≥302under normal traffic conditions, CV≥537at maximum flow rate.. Flow coefficient CV CV ≥3.42at minimum flow rate..CV≥29 under normal traffic conditions.CV≥ 142at maximum flow rate..Open sized 10%-90% Open sized 10%-90% Open sized 10%-90%Bidders must submit a performance table for regulating valves in the prescribed format and provide relevant performance certification documents. The performance certification documents include but are not limited to: 1) a copy of the sales contract and 2) arrival acceptance materials signed or stamped by the user (arrival acceptance form or commissioning acceptance report or other valid proof materials that can prove that the goods under the contract have been received and accepted). The performance certification documents submitted by the bidder must at least reflect the following contents: contract signing time, contract signing page (domestic trade contracts should have both parties' seals, international trade contracts should have both parties' signatures or seals), manufacturer name, goods name, brand and production factory address, supply quantity, technical parameters/indicators (including at least valve body material, valve body class, valve body type, valve body type, CV value, valve allowable opening and calculation sheet), and arrival acceptance materials signed or stamped by the user. If the performance contract is an annual agreement, in addition to providing the annual agreement, corresponding received orders should also be provided, and the order content or number should be associated with the annual agreement. Providing one or more orders and corresponding arrival acceptance materials under the same annual agreement is considered as one valid performance. Failure to submit performance certification documents, or failure to meet the above performance requirements through the provided performance certification documents, shall be deemed as invalid performance.2010年1月1日至投标截止日（以合同签订时间为准），投标人所投调节阀的制造商必须至少有3台气动调节阀和2台电动调节阀配套供货业绩。投标人所投的调节阀的品牌和生产工厂 业绩中的技术指标应全部达到或超过以下技术要求：业绩要求1 业绩要求2 业绩要求3气动调节阀 气动调节阀 电动调节阀业绩要求：1套 业绩要求：2套 业绩要求：2套阀体材质 A182 F51 或A995 Gr.4A 阀体材质 A995 Gr.4A 阀体材质 A995 Gr.4A阀体尺寸 ≥20” 阀体尺寸 ≥14” 阀体尺寸 ≥3”阀体磅级 ≥1500# 阀体磅级 ≥600# 阀体磅级 ≥300#阀体类型 V-Ball 或 Globe 阀体类型 Globe 阀体类型 Globe流量系数CV 最小流量的情况下CV ≥261正常流量的情况下CV≥1814最大流量的情况下CV≥ 4201 流量系数CV 最小流量的情况下CV ≥67.4正常流量的情况下CV≥302最大流量的情况下CV≥ 537 流量系数CV 最小流量的情况下CV ≥3.42正常流量的情况下CV≥29最大流量的情况下CV≥ 142开度 10%-90% 开度 10%-90% 开度 10%-90%投标人须按规定格式提交调节阀业绩表，并提交相关业绩证明文件。业绩证明文件包括但不限于：1）销售合同复印件和2）用户签字或盖章的到货验收材料（到货验收单或调试验收报告或其他可以证明合同项下货物已经到货验收的有效证明材料）。投标人所提交的业绩证明文件必须至少体现以下内容：合同签署时间、合同签署页（国内贸易合同应有双方盖章，国际贸易合同应有双方签字或盖章）、制造商名称、货物名称、品牌及生产工厂 若业绩合同为年度协议，除提供年度协议外，还应提供相应的已到货订单，订单内容或编号应与年度协议相关联。同一个年度协议下提供1个或以上的订单及与订单对应的到货验收材料均算为1个有效业绩。未提交业绩证明文件，或通过所提供的业绩证明文件无法认定满足上述业绩要求的，均视为无效业绩。B.The brand of the actuator shall meet the requirements of Appendix A. Bidders may recommend other brands that meet the following conditions and are equivalent to the recommended brand in Appendix A. From January 1, 2010 to the bidding deadline (based on the time of contract signing), the bidder or the manufacturer of the actuator submitted by the bidder shall have a performance of supplying no less than 2 regulating valves, and the brand and model of the actuator in the performance shall be consistent with the one used in this bidding. If the actuator is used on a pneumatic regulating valve, the material of the regulating valve body in the performance should be A182F51, the valve body size should be ≥ 20 ", and the valve body pressure scale should be ≥ 1500 #; If the actuator is used on an electric regulating valve, the valve body material of the regulating valve in the performance should be A182F51, the valve body size should be ≥ 3 ", and the valve body pressure rating should be ≥ 300 #. Bidders of other brands equivalent to the recommended brand must provide performance certification documents,★The performance certification documents include but are not limited to: 1) a copy of the sales contract and 2) arrival acceptance materials signed or stamped by the user (arrival acceptance form or commissioning acceptance report or other valid proof materials that can prove that the goods under the contract have been received and accepted). The performance certification documents submitted by the bidder must at least reflect the following contents: contract signing time, contract signing page (domestic trade contracts should have both parties' seals, international trade contracts should have both parties' signatures or seals), manufacturer name, goods name, model and production factory address, supply quantity, technical parameters/indicators (including at least valve body material, valve body size,valve body class, valve body type), and arrival acceptance materials signed or stamped by the user. If the performance contract is an annual agreement, in addition to providing the annual agreement, corresponding received orders should also be provided, and the order content or number should be associated with the annual agreement. Providing one or more orders and corresponding arrival acceptance materials under the same annual agreement is considered as one valid performance. Failure to submit performance certification documents, or failure to meet the above performance requirements through the provided performance certification documents, shall be deemed as invalid performance.he brand of the actuator should meet the requirements of Appendix A. Bidders may recommend other brands that meet the following conditions and are of the same level as the recommended brand in Appendix A. From January 1, 2010 to the bidding deadline (based on the contract signing time), the bidder shall have a performance of supplying no less than 2 sets/sets of regulating valves for key components of the same level brand. If the actuator is used on pneumatic regulating valves, the material of the regulating valve in the performance should be A182F51, size ≥ 20 ", and pressure rating ≥ 1500 #; If the actuator is used on an electric control valve, the material of the control valve in the performance should be A182F51, size ≥ 3 ", pressure rating ≥ 300 #. It is recommended that bidders of other brands in the same grade provide performance certification documents. The corresponding performance certification document requirements are detailed in the following performance requirements 1 and 2;Performance Requirement 1Copy of sales contract reflecting the recommended brand and model (including contract cover and signature page, as well as relevant technical attachments)Arrival acceptance materials (buyer's signed or stamped arrival acceptance form, on-site debugging report, usage certificate, or acceptance certificate)Performance Requirement 2The performance certification documents submitted by the bidder must at least reflect the following contents: brand and production factory, technical parameters of supporting control valves, supply quantity, usage environment, technical parameters/indicators, and arrival acceptance materials. Failure to submit performance certification documents, or if the provided performance certification documents cannot verify the above content, shall be deemed as invalid performance. 执行机构的品牌应满足附录A要求，投标人可推荐满足以下条件与附录A或相当于推荐品牌的其它品牌。2010年 1 月 1 日至投标截止日（以合同签署时间为准）投标人或投标人所投执行机构的制造商应具有不少于2台调节阀供货的业绩，且业绩中执行机构的品牌与型号应与本次投标所用的一致。若该执行机构使用在气动调节阀上，则业绩中的调节阀阀体的材质应为A182F51，阀体尺寸≥20”，阀体压力磅级≥1500#；若该执行机构使用在电动调节阀上，则业绩中的调节阀的阀体材质应为A182F51，阀体尺寸≥3”，阀体压力磅级≥300#，推荐相当于推荐品牌的其它品牌的投标人须提供业绩证明文件，业绩证明文件包括但不限于：1）销售合同复印件和2）用户签字或盖章的到货验收材料（到货验收单或调试验收报告或其他可以证明合同项下货物已经到货验收的有效证明材料）。投标人所提交的业绩证明文件必须至少体现以下内容：合同签署时间、合同签署页（国内贸易合同应有双方盖章，国际贸易合同应有双方签字或盖章）、制造商名称、货物名称、型号及生产工厂 若业绩合同为年度协议，除提供年度协议外，还应提供相应的已到货订单，订单内容或编号应与年度协议相关联。同一个年度协议下提供1个或以上的订单及与订单对应的到货验收材料均算为1个有效业绩。未提交业绩证明文件，或通过所提供的业绩证明文件无法认定满足上述业绩要求的，均视为无效业绩。是否接受联合体投标:不接受未领购招标文件是否可以参加投标:不可以4、
未曾在中国电力招标采购网（www.dlztb.com）上注册会员的单位应先注册。登录成功后根据招标公告的相说明下载投标文件！

项目 联系人：李杨  
咨询电话：010-51957458 
传真：010-51957412 
手机：13683233285 
QQ:1211306049 
微信：Li13683233285 邮箱：1211306049@qq.com

备注：欲购买招标文件的潜在投标人,注册网站并缴纳因特网技术服务费后，查看项目业主，招标公告，中标公示等，并下载资格预审范围，资质要求，招标清单，报名申请表等。为保证您能够顺利投标，具体要求及购买标书操作流程按公告详细内容为准，以招标业主的解答为准本。

编辑：chinabidding.co